Zektor ProAudio 16™ DSP Preamp Audio Matrix Instrukcja Użytkownika

Advanced Audio 16x16 Matrix Switch(For ClarityAudio firmware Versions 1.00 and above.)Clarity Audio 16x16User GuideandSerial & TCP/IP Protocols

8ClarityAudio Serial Protocol, Version 1.01, 11/8/12Basic ControlBasic ControlReference for Basic Control CommandsThese commands are all that are need

ClarityAudio Serial Protocol, Version 1.01, 11/8/129Basic ControlBasic Control Commands Basic Command Definitions‘P’ Power ControlTurn on / off, or to

10ClarityAudio Serial Protocol, Version 1.01, 11/8/12Basic Control^=SZ @zone,in$ or,^=SZ.ch @zone,in$Where:@zone = One (or more) zones to be mapped.in

ClarityAudio Serial Protocol, Version 1.01, 11/8/1211Basic ControlIf digital audio, and analog audio, from input ‘3’ are all mapped to zone ‘1’, then:

12ClarityAudio Serial Protocol, Version 1.01, 11/8/12Basic Control‘MZ’ Mute Zone(s)This is the command used to mute any number of zones. When audio is

ClarityAudio Serial Protocol, Version 1.01, 11/8/1213Basic ControlWhere:@zone = One (or more) zones to be mapped.delay = The delay time in millisecond

14ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio ControlAudio ControlReference for Audio Control CommandsThe commands are used to control th

ClarityAudio Serial Protocol, Version 1.01, 11/8/1215Audio ControlResponse Strings:^=MV vol$Where:vol = Volume in 0.5dB steps with an offset of 200. R

16ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio Controlless of the mute setting. The mute setting will be cancelled (unmuted), but will not

ClarityAudio Serial Protocol, Version 1.01, 11/8/1217Audio Controlwill fade zones 1 and 2 to the a level of 20. Regardless of their current values, zo

2ClarityAudio User Guide, Version 1.01, 11/8/12History2012-11-08 Version 1.01• Fixed typos.• Document the ‘DZ’ command.• Document the TCP/IP related c

18ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio Control‘VMAZ’ Set Zone’s Maximum VolumeEach zone has a minimum and maximum volume setting.

ClarityAudio Serial Protocol, Version 1.01, 11/8/1219Audio Control^=VPZ @zone,vol$Where:@zone = One (or more) zones to be affected.vol = Volume as a p

20ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio ControlThe VMZ command allows you to mute the volume on the ClarityAudio using the audio pr

ClarityAudio Serial Protocol, Version 1.01, 11/8/1221Audio ControlTo fade to a new level over a given period of time, add 10000 to any mute level sett

22ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio ControlEach zone has a balance level that can be set from 0 attenuation (full left), to 400

ClarityAudio Serial Protocol, Version 1.01, 11/8/1223Audio ControlEach input has a gain level that can be set from -24dB to +24dB. The gain control al

24ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio Control@zone = One (or more) zones to be affected.level = Levels 0.5dB steps with offsets o

ClarityAudio Serial Protocol, Version 1.01, 11/8/1225Audio Control^EQ1Z @zone,-step$ Subtract ‘step’ number of 0.5dB steps from current level.^EQ1Z ?$

26ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio Control@zone = One (or more) zones to be affected.mix = Stereo mix down flag.0 = No change

ClarityAudio Serial Protocol, Version 1.01, 11/8/1227Audio Control@zone = One (or more) zones to be affected.delay = Lip sync delay in 48KHz samples,

ClarityAudio Serial Protocol, Version 1.01, 11/8/121RS-232 / TCP/IP Port Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28ClarityAudio Serial Protocol, Version 1.01, 11/8/12Audio ControlThere are two forms of the lip sync delay commands, the ‘LSZ’ command which sets lip

ClarityAudio Serial Protocol, Version 1.01, 11/8/1229Advanced ControlAdvanced ControlReference for Advance Control CommandsThese commands are for more

30ClarityAudio Serial Protocol, Version 1.01, 11/8/12Advanced Controldzones = Number of digital audio zones‘XS’ Control SettingsTurn on and off operat

ClarityAudio Serial Protocol, Version 1.01, 11/8/1231Advanced Control‘ACK’ Enable / Disable AcknowledgementsEach time a command is sent to the Clarity

32ClarityAudio Serial Protocol, Version 1.01, 11/8/12Advanced Controlputs, and the analog audio will be routed to the analog outputs. Volume and Tone

ClarityAudio Serial Protocol, Version 1.01, 11/8/1233Advanced ControlThis command uses a bitmapped parameter to indicate which values are to be reset.

34ClarityAudio Serial Protocol, Version 1.01, 11/8/12Advanced ControlTCP/IP ControlThe ClarityAudio can use DHCP to negotiate an address with a router

ClarityAudio Serial Protocol, Version 1.01, 11/8/1235Advanced Control‘IPA’ Set / View the static IP AddressThis command does not immediately change th

36ClarityAudio Serial Protocol, Version 1.01, 11/8/12Advanced ControlThe response string of the ‘IPG’ command is not the current gateway address of th

2ClarityAudio Serial Protocol, Version 1.01, 11/8/12‘IPSET’ Set the IP operation mode, DHCP or STATIC . . . . . . . . . . . . . . . . . . . . . . . .

ClarityAudio Serial Protocol, Version 1.01, 11/8/123RS-232 / TCP/IP Port HardwareRS-232 / TCP/IP Port HardwareTCP/IP OverviewThe Serial and TCP/IP por

4ClarityAudio Serial Protocol, Version 1.01, 11/8/12RS-232 / TCP/IP Port HardwarePort Number: 50005Duplex: Half/Full (auto detect)Speed: 10/100 Mbps (

ClarityAudio Serial Protocol, Version 1.01, 11/8/125Command SyntaxCommand SyntaxCommand SyntaxThe ClarityAudio serial command set uses an ASCII based

6ClarityAudio Serial Protocol, Version 1.01, 11/8/12Command SyntaxThe Error ResponseEvery command will be followed by an acknowledgement or error resp

ClarityAudio Serial Protocol, Version 1.01, 11/8/127Command Syntax^P ?$ -> Send a power request command to the A/V switch^+$ <- Acknowledgement